• GL414BPE
    L14-S14 – BP – PVC

    Load capacity up to 125Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GL414C
    L14-S14 – C – CELERON

    Load capacity up to 300Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).

    Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.

  • GL414FE
    L14-S14 – F – CAST IRON

    Load capacity up to 300Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).

    Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • GL414NPE
    L14-S14 – NP – POLYPROPYLENE

    Load capacity up to 165Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    RODA

    NP – Polypropylene Hardness: 65 Shore D. (-20°C to +70°C).

    Injected with recyclable polypropylene copolymer wheel center and tread. Indicated for light and medium loads, roll very easily, requiring low handling effort, resistant to deformation under static loads, with an excellent cost-benefit ratio. They present a good resistance to chemicals and moderate impacts. Nominal working speed is up to 4km/h. Produced with recycled materials.

  • GL414NU
    L14-S14 – NU – MOLDED POLYURETHANE

    Load capacity up to 165Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NU – Molded polyurethane with Nylon Wheel Center. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and injected nylon wheel center. The mechanical bond system ensures excellent resistance and service life. Ideal for applications on various surfaces and environment types. They are light, withstand high loads, protect the floor, require less effort to handle and produce low noise level during handling. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They may be used in a speed up to 4km/h.

  • GL414PE
    L14-S14 – P – MOLDED POLYURETHANE

    Load capacity up to 300Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 4km/h.

  • GL414PMN
    L14-S14 – PMN – MOLDED RUBBER

    Load capacity up to 120Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    RODA

    PMN – Molded Rubber With Polypropylene Whell Center: 80 Shore A. (-20°C to +70°C).

    Produced with solid rubber tread, with injected polypropylene wheel center. They are light and resistant, withstand humidity, have a soft and quiet rolling and are indicated for light duties on floors in good conditions. Nominal working speed is up to 4km/h.

  • GL414SPE
    L14-S14 – SP – SOFT RUBBER

    Load capacity up to  125Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    SP – Extra Soft Thermoplastic Rubber. Hardness: 65 Shore A. (-10°C to +50°C).

    Injected recyclable thermoplastic extra soft rubber tread and polypropylene copolymer wheel center. Its advantages are the extremely low noise level and vibration reduction. Indicated for light load handling, they offer an excellent floor protection and regular resistance to impacts and chemicals. Nominal working speed is up to 4km/h.

  • alp-L14
    L14-S14 – TB – THERMOPLASTIC RUBBER

    Load capacity up to 125Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    RODA

    TB – Thermoplastic Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with recyclable thermoplastic elastic rubber tread and polypropylene copolymer wheel center. They present an excellent floor protection, soft and quiet rolling, easiness to handling and maneuvering, impact resistance, have a low deformation index under load and excellent abrasion resistance. They have a good resistance to weathering and chemicals such as salts and greases. Nominal working speed is up to 4km/h.

  • GL414TPE
    L14-S14 – TP – THERMOPLASTIC COMPOUND

    Load capacity up to 150Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    TP – Thermoplastic Compound. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, excellent floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GL414UPE
    L14-S14 – UP – THERMOPLASTIC POLYURETHANE

    Load capacity up to 165Kg

    RIG

    Made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    UP – Thermoplastic Polyurethane. Hardness: 90 Shore A. (-20°C to +70°C).

    Produced with recyclable thermoplastic elastollan polyurethane tread and polypropylene copolymer wheel center. Ideal for those who look for an excellent load capacity added to great floor protection with low noise rolling, offering an excellent resistance to abrasion and impacts. Resistant to greases, mineral oils and some acids. Nominal working speed is up to 4km/h.

  • GS62ACE
    Schioppa GS-GM Caster – AC – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    AC – Molded High Hardness Polyurethane – Round. Hardness: 60 Shore D. (-40°C to +80°C).

    Produced with a high hardness molded green polyurethane tread over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to their polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Nominal working speed is up to 4km/h.

  • GS62BE
    Schioppa GS-GM Caster – B – MOLDED RUBBER

    Load capacity up to 450Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 4km/h.

  • GS62BCE
    Schioppa GS-GM Caster – BC – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GS62BPE
    Schioppa GS-GM Caster – BP – PVC

    Load capacity up to 400Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GS62CE
    Schioppa GS-GM Caster – C – CELERON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).

    Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.

  • GS62FE
    Schioppa GS-GM Caster – F – CAST IRON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).

    Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • GS62ME
    Schioppa GS-GM Caster – ME – POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    RODA

    ME – Double tread Molded Polyurethane – Round. Hardness: side 60 Shore D and center 90 Shore A. (-40°C to +80°C).

    Produced with a double tread molded polyurethane, with green colored high hardness cheeks and softer orange colored polyurethane center, over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to its polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Higher hardness wheel side faces allow for a higher resistance to impacts and a softer center a higher floor friction with a lower handling noise level. They may be employed in a speed up to 4km/h.

  • GS62NTE
    Schioppa GS-GM Caster – NT – TECHNICAL NYLON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NT – Technical Nylon. Hardness: 75 Shore D. (-40°C to +110°C).

    Produced with high quality nylon 6.0 tread and wheel center. They are light and have an excellent mechanical resistance, roll very easily, requiring less effort in maneuvering and handling. Ideal for applications in wet environments, they are resistant to greases, oils, salts and some kinds of acids. Manufactured of recycled material. Nominal working speed is up to 4km/h.

  • GS62NU
    Schioppa GS-GM Caster – NU – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NU – Molded polyurethane with Nylon Wheel Center. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and injected nylon wheel center. The mechanical bond system ensures excellent resistance and service life. Ideal for applications on various surfaces and environment types. They are light, withstand high loads, protect the floor, require less effort to handle and produce low noise level during handling. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They may be used in a speed up to 4km/h.

Showing 21–40 of 94 results