• GMX62BSEPreta
    Schioppa MX Caster – Axial Medium – BS – MOLDED DOUBLE RUBBER

    Load capacity up to 500Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    Wheel

    BS – Double-Layered Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded double-layered vulcanized rubber tread over a grey cast iron wheel center. Ideal for external floor applications, offer a great shock and vibration absorption, high resistance to abrasion and longer service life due to their thicker rubber layer. Resistant to chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GMX62CE
    Schioppa MX Caster – Axial Medium – C – CELERON

    Load capacity up to 800Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    Wheel

    C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).

    Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.

  • GMX62FE
    Schioppa MX Caster – Axial Medium – F – CAST IRON

    Load capacity up to 900Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle.

    Wheel

    F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).

    Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • GMX62ME
    Schioppa MX Caster – Axial Medium – ME – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    Wheel

    ME – Double tread Molded Polyurethane – Round. Hardness: side 60 Shore D and center 90 Shore A. (-40°C to +80°C).

    Produced with a double tread molded polyurethane, with green colored high hardness cheeks and softer orange colored polyurethane center, over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to its polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Higher hardness wheel side faces allow for a higher resistance to impacts and a softer center a higher floor friction with a lower handling noise level. They may be employed in a speed up to 10km/h on floors that are not contaminated with grease or slippery liquids.

  • GMX62NTE
    Schioppa MX Caster – Axial Medium – NT – TECHNICAL NYLON

    Load capacity up to 900Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    Wheel

    NT – Technical Nylon. Hardness: 75 Shore D. (-40°C to +110°C).

    Produced with high quality nylon 6.0 tread and wheel center. They are light and have an excellent mechanical resistance, roll very easily, requiring less effort in maneuvering and handling. Ideal for applications in wet environments, they are resistant to greases, oils, salts and some kinds of acids. Manufactured of recycled material. Nominal working speed is up to 4km/h.

  • GMX62PE
    Schioppa MX Caster – Axial Medium – P – MOLDED POLYURETHANE

    Load capacity up to 900Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GMX62TPEB
    Schioppa MX Caster – Axial Medium – TB – THERMOPLASTIC RUBBER

    Load capacity up to 400Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    Wheel

    TB – Thermoplastic Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with recyclable thermoplastic elastic rubber tread and polypropylene copolymer wheel center. They present an excellent floor protection, soft and quiet rolling, easiness to handling and maneuvering, impact resistance, have a low deformation index under load and excellent abrasion resistance. They have a good resistance to weathering and chemicals such as salts and greases. Nominal working speed is up to 4km/h.

  • GMX62TPPreto
    Schioppa MX Caster – Axial Medium – TP – THERMOPLASTIC COMPOUND

    Load capacity up to 400Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    RODA

    TP – Thermoplastic Compound. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, excellent floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GMX62UPE
    Schioppa MX Caster – Axial Medium – UP – THERMOPLASTIC POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Made of steel with a painted finish and swivel section with two axial ball bearings. Bolted wheel axle

    Wheel

    UP – Thermoplastic Polyurethane. Hardness: 90 Shore A. (-20°C to +70°C).

    Produced with recyclable thermoplastic elastollan polyurethane tread and polypropylene copolymer wheel center. Ideal for those who look for an excellent load capacity added to great floor protection with low noise rolling, offering an excellent resistance to abrasion and impacts. Resistant to greases, mineral oils and some acids. Nominal working speed is up to 4km/h.

  • GGPMX3508PCR
    Schioppa PCX Caster – Pneumatic Axial – PNEUMATIC PC

    Load capacity up to 300Kg

    RIG

    Reinforced rig, made of carbon steel with stamped and machined parts, swivel section with two axial ball bearings. Painted finishing. Bolted wheel axle.

    Wheel

    PC – Pneumatic – Stamped Plate Wheel Center (-20°C to +50°C).

    Manufactured with tire and tube, with painted stamped carbon steel plates. Indicated for applications in irregular floors where handling easiness, and impact and vibration damping is required. They offer an easy maintenance, and their components can be supplied separately. Nominal working speed is up to 4 km/h.

  • GGPMX3508PPR
    Schioppa PCX Caster – Pneumatic Axial – PNEUMATIC PP

    Load capacity up to 220Kg

    RIG

    Reinforced rig, made of carbon steel with stamped and machined parts, swivel section with two axial ball bearings. Painted finishing. Bolted wheel axle.

    Wheel

    PP – Pneumatic – Nylon Wheel Center. (-20°C to +50°C).

    Manufactured with tire and tube and nylon injected wheel center. Indicated for applications in irregular floors where handling easiness, and impact and vibration damping is required. They offer easy maintenance, and their components can be supplied separately. Nominal working speed is up to 4km/h.

  • GGPMX3308PMR
    Schioppa PMX Caster – Solid Tire Axial – PMR – SOLID TIRE

    Load capacity up to 500Kg

    RIG

    Reinforced rig, made of carbon steel with stamped and machined parts, swivel section with two axial ball bearings. Painted finishing. Bolted wheel axle.

    Wheel

    PMX – Solid Rubber. Hardness: 80 Shore A. (-20°C to + 70°C).

    Produced with black solid rubber rim and stamped carbon steel plates for the flanges (wheel center). They do not require maintenance, they do not go flat, easily rolling under obstacles and are indicated for use on irregular floors. Flanges are secured by screws, enabling the mounting and replacement of their components that may be supplied separately.

  • GPX83BE
    Schioppa PX Caster – Super Heavy Axial – B – MOLDED RUBBER

    Load capacity up to 750Kg

    RIG

    Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing Bolted wheel axle.

    Wheel

    B – Molded Rubber. Hardness: 80 Shore A. (-20°C to + 70°C).

    Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GPX83BSE
    Schioppa PX Caster – Super Heavy Axial – BS – MOLDED DOUBLE RUBBER

    Load capacity up to 900Kg

    RIG

    Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing Bolted wheel axle.

    Wheel

    BS – Double-Layered Molded Rubber. Hardness: 80 Shore A. (-20°C to + 70°C).

    Produced with molded double-layered vulcanized rubber tread over a grey cast iron wheel center. Ideal for external floor applications, offer a great shock and vibration absorption, high resistance to abrasion and longer service life due to their thicker rubber layer. Resistant to chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GPX83CE
    Schioppa PX Caster – Super Heavy Axial – C – CELERON

    Load capacity up to 1000Kg

    RIG

    Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing Bolted wheel axle.

    Wheel

    C – Celeron Hardness: 103 Rockwell M. (-30°C to + 120°C).

    Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h

  • GPX83FE
    Schioppa PX Caster – Super Heavy Axial – F – CAST IRON

    Load capacity up to 1400Kg

    RIG

    Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing Bolted wheel axle.

    Wheel

    F – Cast Iron. Hardness: 160 Brinell. (-40°C to + 400°C). Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • nm-nylon
    Schioppa PX Caster – Super Heavy Axial – NM – SOLID NYLON

    Load capacity up to 1400Kg

    RIG

    Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing Bolted wheel axle.

    Wheel

    NM – Solid Nylon. Hardness: 70 Shore D. (-40°C to + 110°C).

    Produced from nylon 6.0 bars. They are light weight, with a good mechanical resistance, roll very easily, requiring less effort in handling and maneuvering, under static loads are resistant to deformation. They withstand light and heavy loads maintaining equipment handling easiness. Ideal for applications in wet environments, they are resistant to chemicals, greases, oils, salts and some kind of acids. Nominal working speed is up to 4km/h.

  • GPX83PE
    Schioppa PX Caster – Super Heavy Axial – P – MOLDED POLYURETHANE

    Load capacity up to 1400Kg

    RIG

    Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing Bolted wheel axle.

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to + 80°C).

    Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 20km/h when mounted with ball bearings.

Showing 61–78 of 78 results