• GKSR62TPPreto
    Schioppa ERGONOMIC Caster – TP – THERMOPLASTIC COMPOUND

    Load capacity up to 400Kg

    RIG

    Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.

    Wheel

    TP – Thermoplastic Compound. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, excellent floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GKSR62UPE
    Schioppa ERGONOMIC Caster – UP – THERMOPLASTIC POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reforçado sem pino central, com pista simples de esferas endurecidas e blindadas. Eixo da roda parafusado.

    Wheel

    UP – Thermoplastic Polyurethane. Hardness: 90 Shore A. (-20°C to +70°C).

    Produced with recyclable thermoplastic elastollan polyurethane tread and polypropylene copolymer wheel center. Ideal for those who look for an excellent load capacity added to great floor protection with low noise rolling, offering an excellent resistance to abrasion and impacts. Resistant to greases, mineral oils and some acids. Nominal working speed is up to 4km/h.

  • GKMP83BE
    Schioppa ERGONOMIC HEAVY DUTY Caster – B – MOLDED RUBBER

    Load capacity up to 750Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GKMP83CE
    Schioppa ERGONOMIC HEAVY DUTY Caster – C – CELERON

    Load capacity up to 1000Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).

    Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.

  • GKMP83FE
    Schioppa ERGONOMIC HEAVY DUTY Caster – F – CAST IRON

    Load capacity up to 1200Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).

    Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • GKMP83PE
    Schioppa ERGONOMIC HEAVY DUTY Caster – P – MOLDED POLYURETHANE

    Load capacity up to 1400Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C). Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GHP150UPE
    Schioppa Evidence Caster – UP Thermoplastic Polyurethane

    Load capacity up to 150Kg

    RIG

    Internal structure made of steel lined with injected parts in order to reduce dust entry and make cleaning easy without taking caster out of service. It has a modern brake system with simple acting and two pedals. ON for acting and OFF for releasing.

    Wheel

    UP – Thermoplastic Polyurethane. Hardness: 90 Shore A. (-20°C to +70°C).

    Produced with recyclable thermoplastic elastollan polyurethane tread and polypropylene copolymer wheel center. Ideal for those who look for an excellent load capacity added to great floor protection with low noise rolling, offering an excellent resistance to abrasion and impacts. Resistant to greases, mineral oils and some acids. Nominal working speed is up to 4km/h.

  • evolution_G
    Schioppa Evolution Caster – BP Thermoplastic Compound with PVC

    Load capacity up to 100Kg

    RIG

    Made of natural nylon 6.0 with double ball raceway.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GL158N
    Schioppa Freezer Caster – N Reinforced Nylon with Glass Fiber, Z Zamak

    Load capacity up to 150Kg

    RIG

    Stamped rig with double ball raceway, white zinc-plated and yellow zinc-plated finishing.

    Wheel

    N – Fiberglass-reinforced Nylon. Hardness: 80 Shore D

    Produced with fiberglass-reinforced nylon 6.6. Indicated for utilization in high and low temperature applications. They are light and have an excellent mechanical resistance, rolling very easily, and requiring less effort in maneuvering and handling. Resistant to grease, oils, and some kinds of acids. Z – Zamak. Hardness: 115 Brinell. Produced with zamak, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • Schioppa Futura Caster
    Schioppa Futura Caster – BP Thermoplastic Compound with PVC

    Load capacity up to 100Kg

    RIG

    Made of natural nylon 6.0 with 30% of fiber glass and double ball raceway.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GS62ACE
    Schioppa GS-GM Caster – AC – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    AC – Molded High Hardness Polyurethane – Round. Hardness: 60 Shore D. (-40°C to +80°C).

    Produced with a high hardness molded green polyurethane tread over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to their polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Nominal working speed is up to 4km/h.

  • GS62BE
    Schioppa GS-GM Caster – B – MOLDED RUBBER

    Load capacity up to 450Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 4km/h.

  • GS62BCE
    Schioppa GS-GM Caster – BC – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GS62BPE
    Schioppa GS-GM Caster – BP – PVC

    Load capacity up to 400Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GS62CE
    Schioppa GS-GM Caster – C – CELERON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).

    Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.

  • GS62FE
    Schioppa GS-GM Caster – F – CAST IRON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).

    Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • GS62ME
    Schioppa GS-GM Caster – ME – POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    RODA

    ME – Double tread Molded Polyurethane – Round. Hardness: side 60 Shore D and center 90 Shore A. (-40°C to +80°C).

    Produced with a double tread molded polyurethane, with green colored high hardness cheeks and softer orange colored polyurethane center, over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to its polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Higher hardness wheel side faces allow for a higher resistance to impacts and a softer center a higher floor friction with a lower handling noise level. They may be employed in a speed up to 4km/h.

  • GS62NTE
    Schioppa GS-GM Caster – NT – TECHNICAL NYLON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NT – Technical Nylon. Hardness: 75 Shore D. (-40°C to +110°C).

    Produced with high quality nylon 6.0 tread and wheel center. They are light and have an excellent mechanical resistance, roll very easily, requiring less effort in maneuvering and handling. Ideal for applications in wet environments, they are resistant to greases, oils, salts and some kinds of acids. Manufactured of recycled material. Nominal working speed is up to 4km/h.

  • GS62NU
    Schioppa GS-GM Caster – NU – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NU – Molded polyurethane with Nylon Wheel Center. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and injected nylon wheel center. The mechanical bond system ensures excellent resistance and service life. Ideal for applications on various surfaces and environment types. They are light, withstand high loads, protect the floor, require less effort to handle and produce low noise level during handling. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They may be used in a speed up to 4km/h.

  • GS62PE
    Schioppa GS-GM Caster – P – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 4km/h.

Showing 81–100 of 223 results