• GGMA82NU
    GSA-GMA – NU – MOLDED POLYURETHANE

    Load capacity up to 550Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NU – Molded polyurethane with Nylon Wheel Center. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and injected nylon wheel center. The mechanical bond system ensures excellent resistance and service life. Ideal for applications on various surfaces and environment types. They are light, withstand high loads, protect the floor, require less effort to handle and produce low noise level during handling. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They may be used in a speed up to 4km/h.

  • GCMX82BE
    Schioppa CMX-CPX Caster – B – MOLDED RUBBER

    Load capacity up to 1000Kg

    RIG

    Reinforced rig with an anti-shock spring system, manufactured in thick carbon steel with stamped and machined parts, swivel section with axial ball bearing and tapered roller bearing. Painted finishing. Bolted wheel axle.

    Wheel

    B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GCMX82BSE
    Schioppa CMX-CPX Caster – BS – MOLDED DOUBLE RUBBER

    Load capacity up to 2000Kg

    RIG

    Reinforced rig with an anti-shock spring system, manufactured in thick carbon steel with stamped and machined parts, swivel section with axial ball bearing and tapered roller bearing. Painted finishing. Bolted wheel axle.

    Wheel

    BS – Double-Layered Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded double-layered vulcanized rubber tread over a grey cast iron wheel center. Ideal for external floor applications, offer a great shock and vibration absorption, high resistance to abrasion and longer service life due to their thicker rubber layer. Resistant to chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GCMX82PE
    Schioppa CMX-CPX Caster – P – MOLDED POLYURETHANE

    Load capacity up to 2000Kg

    RIG

    Reinforced rig with an anti-shock spring system, manufactured in thick carbon steel with stamped and machined parts, swivel section with axial ball bearing and tapered roller bearing. Painted finishing. Bolted wheel axle.

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GDE124BSE
    Schioppa DOLLY Caster – Extra Axial – DE/DERX – BS – MOLDED DOUBLE RUBBER

    Load capacity up to 3600Kg

    RIG

    DE: Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing. Bolted wheel axle. DERX: Reinforced rig, made of carbon steel, swivel section with two ball bearing and taper roller bearings . Painted finishing. Bolted wheel axle.

    Wheel

    BS – Double-Layered Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded double-layered vulcanized rubber tread over a grey cast iron wheel center. Ideal for external floor applications, offer a great shock and vibration absorption, high resistance to abrasion and longer service life due to their thicker rubber layer. Resistant to chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GDE124PE
    Schioppa DOLLY Caster – Extra Axial – DE/DERX – P – MOLDED POLYURETHANE

    Load capacity up to 6000Kg

    RIG

    DE: Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing. Bolted wheel axle. DERX: Reinforced rig, made of carbon steel, swivel section with two ball bearing and taper roller bearings . Painted finishing. Bolted wheel axle.

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 20km/h when mounted with ball bearings.

  • GS62ACE
    Schioppa GS-GM Caster – AC – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    AC – Molded High Hardness Polyurethane – Round. Hardness: 60 Shore D. (-40°C to +80°C).

    Produced with a high hardness molded green polyurethane tread over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to their polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Nominal working speed is up to 4km/h.

  • GS62BE
    Schioppa GS-GM Caster – B – MOLDED RUBBER

    Load capacity up to 450Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

    Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 4km/h.

  • GS62BCE
    Schioppa GS-GM Caster – BC – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GS62BPE
    Schioppa GS-GM Caster – BP – PVC

    Load capacity up to 400Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).

    Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

  • GS62CE
    Schioppa GS-GM Caster – C – CELERON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).

    Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.

  • GS62FE
    Schioppa GS-GM Caster – F – CAST IRON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).

    Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.

  • GS62ME
    Schioppa GS-GM Caster – ME – POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    RODA

    ME – Double tread Molded Polyurethane – Round. Hardness: side 60 Shore D and center 90 Shore A. (-40°C to +80°C).

    Produced with a double tread molded polyurethane, with green colored high hardness cheeks and softer orange colored polyurethane center, over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to its polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Higher hardness wheel side faces allow for a higher resistance to impacts and a softer center a higher floor friction with a lower handling noise level. They may be employed in a speed up to 4km/h.

  • GS62NTE
    Schioppa GS-GM Caster – NT – TECHNICAL NYLON

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NT – Technical Nylon. Hardness: 75 Shore D. (-40°C to +110°C).

    Produced with high quality nylon 6.0 tread and wheel center. They are light and have an excellent mechanical resistance, roll very easily, requiring less effort in maneuvering and handling. Ideal for applications in wet environments, they are resistant to greases, oils, salts and some kinds of acids. Manufactured of recycled material. Nominal working speed is up to 4km/h.

  • GS62NU
    Schioppa GS-GM Caster – NU – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    NU – Molded polyurethane with Nylon Wheel Center. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and injected nylon wheel center. The mechanical bond system ensures excellent resistance and service life. Ideal for applications on various surfaces and environment types. They are light, withstand high loads, protect the floor, require less effort to handle and produce low noise level during handling. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They may be used in a speed up to 4km/h.

  • GS62PE
    Schioppa GS-GM Caster – P – MOLDED POLYURETHANE

    Load capacity up to 700Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).

    Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 4km/h.

  • GS2504RIT
    Schioppa GS-GM Caster – RIT – PNEUMATIC

    Load capacity up to 100Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    RIT – Pneumatic – Stamped Plate Wheel Center (-20°C to +50°C).

    Manufactured with tire and tube, with zinc-plated stamped carbon steel plates. Indicated for applications in irregular floors where handling easiness, impact and vibration damping is required. They offer an easy maintenance, and their components can be supplied separately. Nominal working speed is up to 4km/h.

  • GS2504RITPP
    Schioppa GS-GM Caster – RIT PP – PNEUMATIC

    Load capacity up to 100Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    RIT PP – Pneumatic – Nylon Wheel Center. (-20°C to +50°C).

    Manufactured with tire and tube and nylon injected wheel center. Indicated for applications in irregular floors where handling easiness, and impact and vibration damping is required. They offer easy maintenance, and their components can be supplied separately. Nominal working speed is up to 4km/h.

  • GS62SPE
    Schioppa GS-GM Caster – SP – SOFT RUBBER

    Load capacity up to 400Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    SP – Extra Soft Thermoplastic Rubber. Hardness: 65 Shore A. (-10°C to +50°C).

    Injected recyclable thermoplastic extra soft rubber tread and polypropylene copolymer wheel center. Its advantages are the extremely low noise level and vibration reduction. Indicated for light load handling, they offer an excellent floor protection and regular resistance to impacts and chemicals. Nominal working speed is up to 4km/h.

  • GS62STR
    Schioppa GS-GM Caster – STR – THERMOPLASTIC RUBBER

    Load capacity up to 250Kg

    RIG

    Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.

    Wheel

    STR – Thermoplastic Rubber. Hardness: 70 Shore A. (-20°C to +70°C).

    Produced with recyclable thermoplastic rubber tread and polypropylene copolymer center. Wheel tread profile has a grooved pattern enabling a better adherence in external and internal floors. They offer a soft and quiet rolling, excellent floor protection, good chemical resistance, and wear and impact resistance. Nominal working speed is up to 4km/h.

Showing 1–20 of 90 results