Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).
Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).
Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.
| download-catalogo | www.uol.com.br |
|---|
Load capacity up to 6000Kg
RIG
DE: Reinforced rig, made of carbon steel, swivel section with axial ball bearing and taper roller bearings. Painted finishing. Bolted wheel axle. DERX: Reinforced rig, made of carbon steel, swivel section with two ball bearing and taper roller bearings . Painted finishing. Bolted wheel axle.
Wheel
P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).
Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 20km/h when mounted with ball bearings.
Load capacity up to 800Kg
RIG
Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.
Wheel
C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).
Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.
Load capacity up to 400Kg
RIG
Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.
Wheel
TP – Thermoplastic Compound. Hardness: 80 Shore A. (-10°C to +50°C).
Produced with recyclable thermoplastic compound tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, excellent floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.
Load capacity up to 800Kg
RIG
Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.
Wheel
BC – Molded Polyurethane – Round. Hardness: 90 Shore A. (-40°C to +80°C).
Produced with a molded polyurethane tread and grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to their polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents.They can be used at a speed of up to 20km/h when mounted with ball bearings.
