-
Schioppa ERGONOMIC Caster – TP – THERMOPLASTIC COMPOUND
Load capacity up to 400Kg
RIG
Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.
Wheel
TP – Thermoplastic Compound. Hardness: 80 Shore A. (-10°C to +50°C).
Produced with recyclable thermoplastic compound tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, excellent floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.
-
Schioppa ERGONOMIC Caster – UP – THERMOPLASTIC POLYURETHANE
Load capacity up to 700Kg
RIG
Reforçado sem pino central, com pista simples de esferas endurecidas e blindadas. Eixo da roda parafusado.
Wheel
UP – Thermoplastic Polyurethane. Hardness: 90 Shore A. (-20°C to +70°C).
Produced with recyclable thermoplastic elastollan polyurethane tread and polypropylene copolymer wheel center. Ideal for those who look for an excellent load capacity added to great floor protection with low noise rolling, offering an excellent resistance to abrasion and impacts. Resistant to greases, mineral oils and some acids. Nominal working speed is up to 4km/h.
-
Schioppa ERGONOMIC HEAVY DUTY Caster – B – MOLDED RUBBER
Load capacity up to 750Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).
Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.
-
Schioppa ERGONOMIC HEAVY DUTY Caster – C – CELERON
Load capacity up to 1000Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).
Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.
-
Schioppa ERGONOMIC HEAVY DUTY Caster – F – CAST IRON
Load capacity up to 1200Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).
Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.
-
Schioppa ERGONOMIC HEAVY DUTY Caster – P – MOLDED POLYURETHANE
Load capacity up to 1400Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C). Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 20km/h when mounted with ball bearings.
-
Schioppa GS-GM Caster – AC – MOLDED POLYURETHANE
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
AC – Molded High Hardness Polyurethane – Round. Hardness: 60 Shore D. (-40°C to +80°C).
Produced with a high hardness molded green polyurethane tread over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to their polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – B – MOLDED RUBBER
Load capacity up to 450Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).
Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 4km/h.
-
Schioppa GS-GM Caster – BC – MOLDED POLYURETHANE
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).
Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – BP – PVC
Load capacity up to 400Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
BP – Thermoplastic Compound with PVC. Hardness: 80 Shore A. (-10°C to +50°C).
Produced with recyclable thermoplastic compound with PVC tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, great floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – C – CELERON
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).
Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – F – CAST IRON
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
F – Cast Iron. Hardness: 160 Brinell. (-40°C to +400°C).
Produced with grey cast iron, they roll easily offering a great handling effort reduction. They are very resistant withstanding high loads and temperatures. They are not indicated to utilization when noise level and floor maintenance are required.
-
Schioppa GS-GM Caster – ME – POLYURETHANE
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
RODA
ME – Double tread Molded Polyurethane – Round. Hardness: side 60 Shore D and center 90 Shore A. (-40°C to +80°C).
Produced with a double tread molded polyurethane, with green colored high hardness cheeks and softer orange colored polyurethane center, over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to its polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Higher hardness wheel side faces allow for a higher resistance to impacts and a softer center a higher floor friction with a lower handling noise level. They may be employed in a speed up to 4km/h.
-
Schioppa GS-GM Caster – NT – TECHNICAL NYLON
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
NT – Technical Nylon. Hardness: 75 Shore D. (-40°C to +110°C).
Produced with high quality nylon 6.0 tread and wheel center. They are light and have an excellent mechanical resistance, roll very easily, requiring less effort in maneuvering and handling. Ideal for applications in wet environments, they are resistant to greases, oils, salts and some kinds of acids. Manufactured of recycled material. Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – NU – MOLDED POLYURETHANE
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
NU – Molded polyurethane with Nylon Wheel Center. Hardness: 90 Shore A. (-40°C to +80°C).
Produced with a molded polyurethane tread and injected nylon wheel center. The mechanical bond system ensures excellent resistance and service life. Ideal for applications on various surfaces and environment types. They are light, withstand high loads, protect the floor, require less effort to handle and produce low noise level during handling. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They may be used in a speed up to 4km/h.
-
Schioppa GS-GM Caster – P – MOLDED POLYURETHANE
Load capacity up to 700Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
P – Molded Polyurethane. Hardness: 90 Shore A. (-40°C to +80°C).
Produced with a molded polyurethane tread and grey cast iron wheel center. Ideal for applications on various surfaces and environment types The withstand high loads, protect the floor, require less effort to handle, produce low noise level during handling, and have an excellent service life. They have great resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. They can be used at a speed of up to 4km/h.
-
Schioppa GS-GM Caster – RIT – PNEUMATIC
Load capacity up to 100Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
RIT – Pneumatic – Stamped Plate Wheel Center (-20°C to +50°C).
Manufactured with tire and tube, with zinc-plated stamped carbon steel plates. Indicated for applications in irregular floors where handling easiness, impact and vibration damping is required. They offer an easy maintenance, and their components can be supplied separately. Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – RIT PP – PNEUMATIC
Load capacity up to 100Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
RIT PP – Pneumatic – Nylon Wheel Center. (-20°C to +50°C).
Manufactured with tire and tube and nylon injected wheel center. Indicated for applications in irregular floors where handling easiness, and impact and vibration damping is required. They offer easy maintenance, and their components can be supplied separately. Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – SP – SOFT RUBBER
Load capacity up to 400Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
SP – Extra Soft Thermoplastic Rubber. Hardness: 65 Shore A. (-10°C to +50°C).
Injected recyclable thermoplastic extra soft rubber tread and polypropylene copolymer wheel center. Its advantages are the extremely low noise level and vibration reduction. Indicated for light load handling, they offer an excellent floor protection and regular resistance to impacts and chemicals. Nominal working speed is up to 4km/h.
-
Schioppa GS-GM Caster – STR – THERMOPLASTIC RUBBER
Load capacity up to 250Kg
RIG
Reinforced rig, made of stamped steel plate and swivel head with double ball raceway, zinc-plated finish. Bolted wheel axle.
Wheel
STR – Thermoplastic Rubber. Hardness: 70 Shore A. (-20°C to +70°C).
Produced with recyclable thermoplastic rubber tread and polypropylene copolymer center. Wheel tread profile has a grooved pattern enabling a better adherence in external and internal floors. They offer a soft and quiet rolling, excellent floor protection, good chemical resistance, and wear and impact resistance. Nominal working speed is up to 4km/h.
Showing 61–80 of 118 results
