Schioppa Rodas e Rodízios - Schioppa GS-GM Caster - RIT PP

download-catalogo	www.uol.com.br

Read more
Adicionar aos meus desejos

Produto adicionado! Veja sua lista de desejos!

Esse produto já se encontra na sua lista de desejos! Veja sua lista de desejos!

Load capacity up to 800Kg

RIG

Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.

Wheel

C – Celeron Hardness: 103 Rockwell M. (-30°C to +120°C).

Manufactured with a compound obtained from macerated cotton fibers drenched with phenolic resin, molded by heat and pressure. They have excellent mechanical properties, are light and rugged, resistant to deformation under static loads and roll easily. They can be used over a wide temperature range. They are resistant to mild oils, greases and acids in low concentrations. Not recommended for applications in wet environments in contact with alkaline substances. (e.g., caustic soda, chlorine, cleaning products, soap and detergent). Nominal working speed is up to 4km/h.

Read more
Adicionar aos meus desejos

Produto adicionado! Veja sua lista de desejos!

Esse produto já se encontra na sua lista de desejos! Veja sua lista de desejos!

Schioppa ERGONOMIC Caster – ME – MOLDED POLYURETHANE

Load capacity up to 800Kg

RIG

Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.

RODA

ME – Double tread Molded Polyurethane – Round. Hardness: side 60 Shore D and center 90 Shore A. (-40°C a +80°C).

Produced with a double tread molded polyurethane, with green colored high hardness cheeks and softer orange colored polyurethane center, over a grey cast iron wheel center. Round tread profile offers a reduced floor contact area, easiness for handling and maneuvering, reducing handling effort and low rolling noise level. They offer a superior service life due to its polyurethane layer larger than conventional wheels. They have an excellent resistance to abrasion, impacts, weathering and chemicals such as greases, oils, salts and solvents. Higher hardness wheel side faces allow for a higher resistance to impacts and a softer center a higher floor friction with a lower handling noise level. They may be employed in a speed up to 20km/h on floors that are not contaminated with grease or slippery liquids.

Read more
Adicionar aos meus desejos

Produto adicionado! Veja sua lista de desejos!

Esse produto já se encontra na sua lista de desejos! Veja sua lista de desejos!

Schioppa ERGONOMIC Caster – TP – THERMOPLASTIC COMPOUND

Load capacity up to 400Kg

RIG

Reinforced without central pin, with single hardened and guarded ball raceway. Bolted wheel axle.

Wheel

TP – Thermoplastic Compound. Hardness: 80 Shore A. (-10°C to +50°C).

Produced with recyclable thermoplastic compound tread and polypropylene copolymer wheel center. They offer a soft and quiet rolling, excellent floor protection, good chemical, wear and impact resistance, resulting in an excellent cost-benefit ratio. Nominal working speed is up to 4km/h.

Read more
Adicionar aos meus desejos

Produto adicionado! Veja sua lista de desejos!

Esse produto já se encontra na sua lista de desejos! Veja sua lista de desejos!

Schioppa CMX-CPX Caster – B – MOLDED RUBBER

Load capacity up to 1000Kg

RIG

Reinforced rig with an anti-shock spring system, manufactured in thick carbon steel with stamped and machined parts, swivel section with axial ball bearing and tapered roller bearing. Painted finishing. Bolted wheel axle.

Wheel

B – Molded Rubber. Hardness: 80 Shore A. (-20°C to +70°C).

Produced with molded vulcanized rubber tread over a grey cast iron wheel center. They roll softly with a low noise level, absorb shocks and vibrations. They are resistant to abrasion and chemicals. They can be used at a speed of up to 20km/h when mounted with ball bearings.

Schioppa GS-GM Caster – RIT PP – PNEUMATIC

Additional information

Schioppa GS-GM Caster – RIT PP – PNEUMATIC

Additional information

Related Products